New XPROG-m 5.0

18 адаптеров

Не блокируется

   

The XPROG-m programmer is designed to replace the earlier version of  XPROG programmer.

XPROG-m programmer is fully upward-compatible hardware with XPROG programmer and have many additional features.

The XPROG-m supports in-circuit or on-board programming of Motorola 68HC05 , 68HC08, 68HC11, 68HC(S)12 , HC912, MC9S12, MC9S12X , Texas Instruments TMS370 , MPC5xx, ST10Fxx, ATmega family MCU's and serial EEPROM's .

All supported devices are divided into "Software authorization" licenses. You can obtain authorization license only for these devices you are interested in.

XPROG-m Rev. E functional features :
 
 Fully compatible with all software versions of " Device Programmer Desktop".
 Software update (ATMEGA) - directly from "Device Programmer Desktop".
 Software version control mechanism.
 Self check for error handling.
 Communication via  USB 1.1 / 2.0   or high speed RS232 interface .
 Fully upward-compatible XPROG connector.
 Multi functional XPROG-m connector.
 8 pin DIP socket for on- board programming.
 Supports many PLCC, QFP, LQFP adapters for on- board programming.
 High speed hardware engine (PLD).
 Two PWM regulated and ADC controlled voltage regulators.
  K-Line interface pin.

Hardware Specifications :

Include high output current MPU.
External output for on-board device programming.
Serial port interface (up to 115K baud) works on (COM1, COM 2, COM3 or COM4).
USB 1.1 / 2.0


Electrical Requirements :
Power consumption : 300 mA.
NOTE:
If programmer connects to PC via RS-232 serial port, an external 12V DC power supply is needed.
 
If programmer connects to PC via USB port ,usually an external power supply is not needed, but be sure that USB can supply enough power.
 


System Requirements for PC :

 Processor: INTEL Pentium 60MHz or faster (depends on operating system)
 Memory (RAM):  32MB (depends on operating system)
 Hard drive:  5MB free space
 Communication: One free physical COM-port or USB  1.1 / 2.0
 Operating system:  Microsoft Windows 95/ 98/ NT/ ME/ 2000/ XP
 
 NOTE:
USB is not supported on Windows NT 4.0 or early versions of Windows 98
 

Motorola HC05 family authorization (allows to read/write EEPROM)
 
    Motorola HC08 family authorization (allows to read/write EEPROM)
 
    Motorola HC11 family authorization (allows to read/write EEPROM)
 
    Motorola HC(S)12 family authorization (allows to read/write EEPROM and flash memory)
 
    Texas Instruments TMS370/TMS374 family authorization  (allows to read/write EEPROM).
 
    Motorola HC05B/X family bypass security authorization (allows to read/write secured EEPROM
    and flash memory )
 
    ST M35080 read/write/erase authorization
      BMW EWS3 authorization.
 
    ATmega family authorization (allows to read/write EEPROM and flash memory)
 
    MB ZGS001 authorization
 
    Motorola HC11EA9/E9 bypass security authorization  (allows to bypass security bit and
    read/write EEPROM )
 
    National CR16 authorization (allows to read/write EEPROM memory)
 
    ST10Fxxx family authorization (allows to read/write flash memory and external EEPROM)
 
    MPC5xx  authorization (depending on device  program automatically detects
    MPC5xx, M95xxx device type, flash, external flash and configuration memory size)
 
    Motorola HC12, HC912, MC9S12, MC9S12X  bypass security authorization (allows to read/write
    secured EEPROM and  flash memory. No need to desolder MCU)
   
 
    ARM (Micronas family) bypass security authorization ( allows to read/write secured and non-secured internal flash and external serial EEPROM. Ability  to view/change mileage, chassis number (VIN), serial number and PIN code with dashboard tools).

Ссылка на софт